How it is worked out
Multiply the length by the width to get the area, add a margin for cut and broken tiles, and divide by the area of one tile.
Example: a 10 × 8 ft floor is 80 sq ft. With 10% extra that is 88 sq ft. A 12 × 24 in tile is 2 sq ft, so you need 88 ÷ 2 = 44 tiles.
Tiles are sold by the box, and the box says how much it covers. 88 sq ft in boxes of 16 sq ft is 5.5, so buy 6 boxes.
How much extra to buy
10% is right for a simple room laid straight. Use 15% for a diagonal or herringbone layout, a room with many corners, or large tiles, where every cut wastes more.
For a wall, measure each wall separately and add them up; leave out a large window or a bath panel.
Buy all the tiles from the same batch (the lot number on the box): shades vary from one batch to the next. Keep a few spare tiles: replacing a cracked one years later is hard when the tile is no longer made.
Tiles per area
| Area | 12 × 12 in tiles | 12 × 24 in tiles | 24 × 24 in tiles |
|---|---|---|---|
| 25 sq ft | 28 | 14 | 7 |
| 50 sq ft | 55 | 28 | 14 |
| 75 sq ft | 83 | 42 | 21 |
| 100 sq ft | 110 | 55 | 28 |
| 150 sq ft | 165 | 83 | 42 |
| 200 sq ft | 220 | 110 | 55 |
| 300 sq ft | 330 | 165 | 83 |
With 10% extra for cuts and breakage. For a diagonal or herringbone layout, use the calculator with 15%.
Worked example: a kitchen floor in large tiles
The open floor of a kitchen is 11 ft 6 in × 9 ft: 11.5 × 9 = 103.5 sq ft. Tiles do not go under built-in base cabinets, so measure only the floor you will see.
The tiles are 24 × 24 in, 4 sq ft each. Large tiles waste more at every cut, so add 15%: 103.5 × 1.15 = 119 sq ft, and 119 ÷ 4 = 29.8, so 30 tiles.
They come 3 to a box (12 sq ft): 119 ÷ 12 = 9.9, so 10 boxes, exactly 30 tiles and not one spare. Buy an 11th box: one tile cracked while cutting and the job stops until the shop opens.
Tiles this size need a flat floor: no more than 1/8 in of dip under a 10 ft straight edge, the limit ANSI A108.02 sets for tiles over 15 in. Check before you buy, so that leveller goes on the list too.
Mistakes to avoid
Measuring the room instead of the floor: take off an island or a bath that stands on the floor, but measure into each doorway to the middle of the door.
Ordering 10% extra for a diagonal or herringbone layout: those cut far more, so allow 15% or more.
Forgetting a tiled skirting: it takes the perimeter times its height. In a 12 × 10 ft room a 3 in skirting is 44 ft × 0.25 ft = 11 sq ft more.
Laying from one box at a time: open three or four and mix the tiles as you go, so small differences in shade spread over the floor instead of showing as patches.
Questions
Does the grout gap change the number of tiles?
Hardly. A 1/8 in joint on a 12 in tile adds about 2% to the area each tile covers, and the extra for cuts more than makes up for it.
How do I measure an L-shaped room?
Split it into two rectangles, work each out, and add the tiles together.
Does this work for flooring planks?
For laminate, vinyl or engineered wood, sold by the pack, use the flooring calculator.